2.5cm ( 1" ) SideWall
Tredwear Classic 1.27cm (1/2″) SideWall
Taking tires from plain to amazing!
Signle wheel kits
How To Order :
Select the font size.
Enter the number of kits your ordering in the quantity or (QTY) field at the bottom
ADHESIVE INCLUDED: With 4 Wheel kits Only
Colours: White are stock items,
Our Normal way of shipping is with Canada Post expedited Parcel.
You can also choose:
PriorityPost NextDay delivery or 1 to 2 days depending on your location.
Parcel xpresspost 3 to 5 days.
This is an extra charge. If you do not want the extra service leave unchecked.
Courier Services are used also by customer’s request. For that item that just have to be there. Call (902) 650-0152 to schedule for a courier Service.
Taking tires from plain to amazing!
NOTE: Our warranty does not cover improperly installed product or exposure to unauthorized chemicals.
Follow ALL directions carefully.
- All kit materials and tires must be dry and kept in a climate no colder than 18º C or 65º F for a minimum of 1 hr before installation.
- Wash & scrub the tire's sidewalls with a strong degreaser and water, (no petroleum,citrus or silicon base products). We recommend (Blast Off an acid base degreaser, 50-2023) then rub dry. Repeat up to 5 applications of washing and scrubbing are required. Note: If using an acid base degreaser its important to use rubber or silicon gloves.
- Next, scuff the surface with 80g sand paper.
- Next, wipe-down the tire sidewall plus the TredWear Classic SIDEWALL with 99% isopropyl alcohol and let air dry.
It is not required, but often, removing the wheel from the vehicle and laying flat will aid in the
installation. Let gravity work with you not against you. Find a line on the tire to follow with the stripe.
(Note: Thin stripes or redlines should be near the middle of the tire or closer to the rim not on the outside edge.) One inch colon/valls or greater should go right against the rim or rim protector bead. Begin gluing the stripe down by applying glue 4-6 inches at a time and smoothing down along the path you are following. Moderate the glue so that it does not squeeze out and run. Continue this process until you reach the final 6-10 inches of stripe. At that time, smooth out the remaining length without glue until reaching the other end of the stripe. Use an exact to or razor blade to trim the length perfectly to match the other side. Apply final glue and smooth the ends together.
Some kits contain a keystone graphic to cover the seam. Apply this as desired. Note: on tires greater than 22" the stripe will not meet the other side and will leave a gap. The decorative tire graphic can be used to fill that gap. "See our page on tire graphics". Check for any loose areas or areas with insufficient glue, and touch up as necessary. Glue will set in as little as 5 to10 seconds. Let tires sit for one hour at temperature for proper adhesion. After installation, a shakedown run of 16 to 32 km or 10 to20 mi at hyw speeds is needed. Check for any loose areas and do a final touch up. Our patented Rubber material will stay white for years. Scrub letters with a nylon bristle brush & Detergent. You could use Whitewall or Letter cleaner use ( All-Off All Purpose Cleaner With Trigger Sprayer # 45-1005 or White Letter Cleaner With Trigger Sprayer #45-1020.)
DO NOT USE BLEACH. DO NOT USE TIRE DRESSING. It can stain the letters.
The All-Off #45-1005 it is a cleaner for your letters and sidewalls. Do not use it for the tire prep its a silicon base product.
The White Letter Cleaner #45-1020 is a cleaner not a degreaser.
902-650-0152 - https://tredwearcanada.ca
There are no reviews for this product.