902.650.0152

9 Whidden Road., Brookfield NS

White Tire Graphics: Maltese Cross

Product Code: 54 1060

Price: $6.80

Available Options

* Extra Shipping:
You can add any additional Information, optional:

>>  ACCESSORIES << 
54-1060 Tire Graphics: Maltese Cross

Unit Size:
  • Centimetres 3.3cm W x 4.6cm H  x 0.1588cm thickness. 
  • Inches   1.3in W x 1.8in H x 1/16″ thickness.
 

Note: 
The item may have a blue or clear protective covering.
<< BACK 
Customer's Install  Guide    TWC LOGO TRANS
 

Note: Don’t install  below 18º C  ( 64º F )
You may choose not to remove your wheel to install your new letters. However, apply your letters to the top half at a time.
This makes it easier to apply the letters to the tire. Either rotate the tire by using the jack. Or, you can roll the vehicle back or foreword.  



Wash your tires with a strong de-greaser. wipe or let air dry. Now Sand with 80g sand paper to the area where the letters are going. Clean the tire several times with acetone tell you don’t see any black residue on your cloth. ( All tire wax and dressings has to be removed ). let dry for 2 to 4 min, then clean with the 99% Isopropyl alcohol or you can use 90% rubbing alcohol. Before installing, bath the letters in the rubbing alcohol, pat and let air dry with a clean cloth. now your ready to install. The 20g bottle of glue will normally do up to three vehicles, put a thin coat of glue on each letter, spread the glue around making sure all corners are covered. so when you place the letter on the tire you’ll have a small beed of glue around the outside edge of the letter. if you don’t have a beed around the letter thats fine. You don’t want a lager glob of glue around your letter, to much glue will cause the glue not to bond properly..


Guide d'installation du client
Note: Ne pas installer en dessous de 18º C ( 64º F )
Vous pouvez choisir de ne pas retirer votre roue pour installer vos nouvelles lettres. Cependant, appliquez vos lettres à la moitié supérieure à la fois.
Cela facilite l'application des lettres au pneu. Soit tourner le pneu en utilisant le cric. Vous pouvez également faire rouler le véhicule en arrière ou en préface.

Bien nettoyer vos pneus à l`aide d`un puissant dégraisseur jusqu’à temps que la surface soit bien adhérente, essuyer et laisser sécher à l`air libre. Sabler la zone avec du papier sablé; grains 80, à l’endroit où vous voulez appliquer le lettrage. Nettoyer le pneu avec de l’ACETONE jusqu`a temps que tous les résidus soit disparus ( Plus aucun résidu noir sur votre chiffon ).
Laissez sécher de 2 à 4 minutes, puis nettoyer avec de l`alcool a friction 99%. Bien assécher la zone avec un chiffon sec. Vous êtes maintenant prêt pour l`installation. Le flacon de 20g de colle sera suffisant pour 3 véhicules. Appliquer une fine couche de colle a l’endos de chaque lettre, étendre sur toute la surface et s`assurer que tous les contours sont couvert. De cette manière vous n`aurez pas de surplus de colle a l’entour de vos lettres. Au contraire, un surplus de colle affectera l’adhésion des lettres.
Ayez du plaisir avec votre installation, au plaisir de vous aider.

PDF Download
PDF Download
There are no reviews for this product.
Write a review
BadExcellent
Facebook comment

NEWS & PROMOTIONS

TESTIMONIALS

"I recently purchased a 30 year old (1985) Mazda RX-7 with such low mileage that it actually still wore the tires it had when it came from the factory. Those tires were very hard and quite cracked, however, so new tires were required: of course, new original tires are no longer available. In fact, there are no tires available for the car that have raised white letters. TredWear Canada provided the only possible solution: they were able to replicate the two distinct fonts of the original 1980's Bridgestones, and within a couple weeks of ordering I had perfectly replicated 1980's period factory-look tires on my car. How else can one enjoy the safety of a current technology tire and yet still maintain the exact look of the car when it was delivered new thirty years ago?"

Regards,
Patrick